By Wayne Burleson
With 30 years of experience building hundreds of Km of electric fence, I’ve seen just about every fencing mistake possible. And I continue to see folks make many of the same common mistakes. I still make mistakes myself, because I’m constantly challenging myself to make fencing easier, faster, stronger, and safer.
With a little commitment and a modest investment in time to learn how to use this new technology, you can save thousands of dollars and hours of maintenance time by making electric fencing work for you. So you won’t have to learn the hard way, here are 19 common mistakes that you should avoid:
Poor earth grounding
Lots of folks (including me) still think you can skimp when it comes to adequate earth grounding. What we must all learn to do, is install several ground rods — at least three that are 2-2.5 meters, galvanised, and attached with good ground clamps. The electricity must complete a full circle back to the charger through the ground. Poor grounding gives weak shocks.
Using different types of metals.
Don’t do it. When you hook up steel wire to copper something call electrolysis happens and the metal becomes corroded, making a poor contact and weakening shocking power.
Inadequate animal training.
Each and every animal must learn that the fence hurts. So please build a handy training fence, preferably on heavy wet soil. Flag the fence for visibility, and force the animal to try and cross the fence.
Fence posts too close together.
Well-intended government agencies recommend lots of fence posts in their fencing specifications. Fifteen meter spacing on flat land is just too close. You want the fence to act like a rubber band. When something runs into the wire, you don’t want to break all the insulators or knock posts out of the ground. If the posts are spread apart far enough — say 25 to 30 meters — the wire will just bend to the ground and pop back up.
Too many wire tie-offs.
Again, fencing specifications may call for braces every 400 meters of wire to tie the wire off. But I have found that even 1.5 km is OK, and actually adds more elasticity in the fence wire. This reduces the chance of wires breaking.
Wires tied tight to each fence post.
To maintain elasticity (the rubber band effect), wires must float past each line fence post.
Building new fences near old existing fences.
Bottom wire in contact with heavy, wet vegetation.
Wet grass will suck lots of juice out of any fence charger. Hook up the lower wires separate from the other wires, and install a switch for the lower wires that you can turn them off when the grass is tall.
Be careful here. Sunlight deteriorates plastic. So buy good-quality, long-lasting insulators. Usually black ones are treated to resist degradation by ultraviolet light. I have found that poor quality insulators turn white or clear after a few years in direct sunlight.
Staples driven in all the way.
When using plastic tubing as an insulator, don’t staple it too tight. I once spent several hours trying to find a short in a gate. Finally, I discovered a staple had damaged the tubing next to a ground wire, causing a hidden short.
Solar panels not directly facing the sun.
This seems almost too obvious to be a problem. But a solar panel won’t function at its potential if not properly installed. Please read the instructions. Don’t just guess if you have done it right.
Kinks in high-tensile wire.
A small kink in stiff wire will always break. Also avoid hitting this kind of wire with a hammer, as this will easily damage the wire causing a break. Always cut out a damaged section of high tensile wire and splice it. Incidentally, I have found that a hand-tied square knot makes the strongest splice.
Installing in-line strainers close together.
Wires will flip together once in awhile. If in-line strainers are installed one above the other, they will sometimes hook up. Separate in-line strainers by a fence post and they will never catch on each other.
Wires too close to each other.
Keep them at least 12 cm apart.
Without a voltage meter to check how hot a fence is, you’re just guessing.
Wire too small.
The larger the wire, the more electricity it will carry. Don’t skimp.
Inadequate charger (energiser).
A wimpy fence charger (also know as energiser or energizer) gives you a wimpy fence. Don’t skimp here because animals will think a smooth wire fence is a joke without a strong bite, and they’ll walk right through it. See our electric fence energiser range here
Your fence charger (energiser) should be low-impedance, come from a dependable supplier, and have a warranty and replaceable components.
Please buy one that puts out lots of power. During a rainy year, you may have lots of plant growth touching the wires. That’s when you will need extra power to shock through the heavy, wet vegetation. It’s also handy to find folks with an extra charger they can loan to you while yours is being repaired. Expect some breakdowns, especially from lightning. Certain fence suppliers offer lightning protection with their warranties.
Don’t be afraid to try electric smooth wire fencing.
Find a good fence supplier and learn some of the tricks of the trade. I know folks who hate electric fencing. But their pocketbook is not big enough to build a conventional fence, which may cost up to an arm and a leg.
The next time your bulls get in a fight with the neighbours bulls and tear down the entire fence, remember that most animals will learn not to touch a wire with 5,000 volts running thorough it.